Pooler, GA
AC repair in Pooler, GA
When an air conditioner in Pooler stops keeping up, the fault can be electrical, refrigerant, airflow, drainage or mechanical — and in a newer home, sometimes how the system was sized and ducted in the first place. We find out which before anything is replaced. The diagnostic is $89, quoted before we start; you approve any repair before work begins; and no-cool emergencies are answered 24/7.
- 1997
- family-owned, a short drive away
- $89
- diagnostic, quoted before we start
- 24/7
- for no-cool emergencies
- Same day
- often available, never promised
What AC problems come up in Pooler homes?
Warm air, weak airflow, a system that never shuts off or keeps short-cycling, water at the indoor unit, ice on the copper line, a new noise, rooms that never match, or a house that feels damp at the right temperature. Each can come from very different faults, so the visit diagnoses the cause instead of treating the symptom — or assuming every cooling problem means low refrigerant.
Running, but not cooling
A dirty filter or coil can starve the system of airflow; the charge can be wrong because of a leak or because it was never set correctly; or the outdoor fan, the compressor or an electrical part may have failed. The symptom alone cannot name the part.
AC running but not coolingIt will not turn on
Check the thermostat, the breaker and the condensate safety switch first. Past those, capacitors, contactors, control boards, motors and wiring need testing rather than guessing.
AC not turning onWater around the indoor unit
The coil pulls moisture out of the air and the condensate system has to carry it away. A blocked line, a dirty pan or a tripped float switch shows up as a puddle — or as a system that suddenly will not run.
AC leaking waterIce on the line or the coil
Restricted airflow and refrigerant problems are the two usual families. Switch cooling off and let it thaw; forcing a badly iced system to keep running makes the fault harder to find.
AC frozen upSome rooms are always hotter
In a newer Pooler house this is often a distribution question — returns, supply balancing, duct leakage or zoning — rather than a broken part. The next chapter covers what gets checked.
Uneven temperaturesCool, but clammy
Temperature and humidity are separate loads. A system can reach the setpoint without removing enough moisture, which points at runtime, airflow and sizing before it points at the thermostat.
House too humidNo cooling at all? Call (912) 858-3737 rather than sending a request — no-cool emergencies are answered 24/7. For a system that still runs but is not right, book a diagnostic visit.
Why can a newer Pooler home still be uncomfortable?
Pooler has grown fast: 25,711 residents in the 2020 Census and about 32,744 by the Census Bureau's 2025 estimate. A newer house is not automatically a trouble-free HVAC house. DOE and ENERGY STAR both name oversizing, incorrect refrigerant charge and leaky ducts as installation problems that cost comfort, efficiency and equipment life — so when a recent home never feels right, the installation is part of the diagnosis.
- 25,711
- residents in the 2020 Census
- 32,744
- Census Bureau estimate for 2025
U.S. Census Bureau, City of Pooler: 2020 Census and Vintage 2025 population estimate.
Sizing and runtime
An oversized system reaches the setpoint quickly, shuts off and starts again. The rooms get cold without the coil running long enough to pull much water out, which is how a new house ends up cool and damp at the same time.
Why square footage is not enoughReturn air and the filter
Too little return capacity, or a filter more restrictive than the system was designed for, starves the blower of air. The symptoms — weak airflow, noise at the grilles, an icing coil — look like equipment faults.
Duct leakage and balancing
Ducts running through a hot attic lose cooling through every leaky joint, and supply runs that were never balanced deliver it to the wrong rooms. Measuring static pressure and airflow shows which one it is.
Refrigerant charge set at install
A system that was never charged correctly will not cool or dehumidify to its rating, however new it is. That is a correction rather than a leak — and the difference matters, because one needs finding and the other does not.
Zoning and the thermostat
Where zoning was installed, a stuck damper or a misconfigured zone board can make one floor miserable. A thermostat in a sunny hallway or beside a supply register can also run the whole house by the wrong room.
From the older streets to Savannah Quarters
Pooler's newer communities — Savannah Quarters, Hamilton Grove, Bridgewater and Harmony among them — sit alongside older streets near the center of town, where ducts, equipment and additions may have been changed over the years. That is a reason to look at the layout in front of us, not an assumption about any one neighborhood.
What Pooler's summers ask of an air conditioner.
Pooler sits beside Savannah/Hilton Head International Airport, whose NOAA 1991–2020 normals show 80.5 days a year at 90°F or hotter and a normal July of 92.3°F by day and 73.7°F at night, with about 48 inches of rain a year. That means long runtimes, little overnight recovery, and a coil that turns a lot of humid air into water the drain has to carry away.
- 80.5
- days a year at 90°F or above
- 92.3° / 73.7°
- normal July high and low, °F
NOAA 1991–2020 Climate Normals, Savannah/Hilton Head International Airport.
Indoor relative humidity
45–55%Clammy and musty
above about 60%
Warm nights give the system little rest
With July nights normally in the low seventies, the house keeps gaining heat after dark and the equipment keeps running. A restricted filter, a dirty coil or a weak capacitor that would go unnoticed in a mild climate tends to show itself here in the middle of summer.
Two jobs: heat and moisture
Cooling a Pooler house means removing heat and water at the same time. The EPA recommends keeping indoor relative humidity below 60%, so a house that holds its temperature but still feels sticky has a real problem to diagnose — not a reason to keep lowering the thermostat. More on humidity and comfort.
Condensate is a maintenance item here
The EPA advises keeping HVAC drain pans clean and drain lines flowing freely. In a long, humid season the drain works hard, and a slow line becomes a leak or a float-switch shutdown sooner than it would elsewhere.
What happens during an AC repair visit?
The visit moves from symptom to measurement to diagnosis, not straight from “it isn’t cooling” to a new part. The technician confirms the complaint, checks the thermostat and airflow, looks at the indoor and outdoor equipment, tests the electrical and refrigerant sides where the symptom points, then explains the finding and the price. Nothing is repaired until you approve it, and the system is tested again afterwards.
Confirm what the system is doing
What the thermostat is calling for, and what the indoor blower and the outdoor unit actually do in response. A no-start, a leak and a humidity complaint each start from a different place.
Airflow and the indoor side
Filter, returns and registers, blower, indoor coil and condensate drain — the checks that explain many complaints before anyone reaches for gauges.
The outdoor unit and the electrical side
Supply and control voltage, capacitor, contactor, fan motor and compressor operation, and the safety switches.
The refrigerant circuit, when indicated
Pressures and charge are checked when the earlier findings point there, and only by an EPA-certified technician. Gauges are not a substitute for verifying airflow first.
The finding, the options and the price
You hear what failed, what we recommend, what it costs and whether anything changes the repair-or-replace picture. The work waits for your approval.
Repair, then verify
After the repair the system runs again so cooling, airflow and drainage can be confirmed — not just that a part was fitted.
Systems and brands we service
We service residential central air conditioners and heat pumps in Pooler, and Brabham is a Trane Authorized Dealer. Another brand? Call (912) 858-3737 with the manufacturer and model number and we will confirm service and parts before the visit.
What is safe to check before you call?
You can confirm the thermostat is on Cool with the setpoint below the room temperature, check whether the breaker has tripped, replace an obviously dirty filter, make sure supply and return grilles are clear, and look for visible ice or water. Stop there. Opening electrical panels, touching capacitors, bypassing a condensate safety or adding refrigerant is technician work.
Thermostat on Cool
Not Fan or Auto-fan alone, with the setpoint a few degrees below the room. New batteries if it takes them.
The breaker, once
If the AC breaker has tripped, switch it fully off, then on — once. If it trips again, leave it off and call.
The filter
A clogged filter cuts airflow, lengthens runtime and adds wear on the blower. Replace it with the size and type the system specifies.
Grilles and the outdoor unit
Open the supply registers, clear the return grille, and pull leaves and debris away from the condenser without opening its panels.
Ice or water
If you see ice, switch cooling off and let it thaw. If there is water, note where it is coming from and keep it away from anything electrical.
Leave these to a technician
- Electrical panels, capacitors and contactors
- Bypassing a float switch or other condensate safety
- Refrigerant lines and adding refrigerant — the EPA requires certification for that work and prohibits venting refrigerant
How much does AC repair cost in Pooler?
Pooler is in Chatham County, so it is priced from the same list as our Savannah work — real numbers, not a national average. The diagnostic is $89, quoted before we start. After the fault is found you get the repair price and approve it before any work. Electrical and drain repairs on that list start in the low hundreds; coils and compressors are a different order of bill.
Our Savannah price list
- Diagnostic / service call
- $89
- Capacitor replacement
- From $179
- Contactor replacement
- From $189
- Condensate drain clearing
- From $149
- Refrigerant recharge
- From $299
- Leak repair + recharge
- $499–$1,299
- Condenser fan motor
- $449–$799
- Blower motor
- $549–$1,099
- Evaporator coil
- $1,295–$2,795
- Compressor
- $1,799–$3,499
- After-hours / emergency
- +$99 dispatch
Prices are starting points for standard work in the Savannah area. Final price depends on the system and site, and is confirmed before work begins. Permits and code-required upgrades may be additional.
On a newer system, check the warranty first
Manufacturer warranties generally cover a failed part and not the labor to fit it, and how long they run depends on the product and on whether it was registered after installation. With a newer Pooler system, have the model number, serial number and install date to hand: a covered part can change the bill considerably.
The final price also moves with the part itself, the refrigerant involved, parts availability, how easy the equipment is to reach, and whether the call is after hours.
Should you repair or replace the AC?
Do not replace a working system on age alone, and do not keep repairing one only because replacement costs more today. Repair deserves serious weight when the failure is isolated and the rest of the system is healthy. Replacement deserves a comparison after a compressor or coil failure, repeated breakdowns, comfort that was never right, or several parts wearing out at once.
Repair usually makes sense when
The failure is isolated, the system otherwise cools and controls humidity properly, the major components are healthy, parts are obtainable, and warranty coverage takes a real share of the cost.
Replacement deserves a comparison when
The compressor or a coil has failed, breakdowns are adding up, the house has never been comfortable, the equipment is well into its life, corrosion or several components are deteriorating together, or the repair leaves another major known problem behind it.
ENERGY STAR suggests having equipment over 10 years old evaluated, especially if it no longer keeps the house comfortable. That is a prompt to compare, not a replacement deadline.
Refrigerant belongs in the calculation, not in a sales pitch. Existing R-22 systems can still legally be serviced, using reclaimed or previously produced refrigerant since U.S. production and import ended in 2020. Existing R-410A systems can be repaired as well — the refrigerant transition limits what new equipment is built with, not whether yours can be fixed.
And if the real problem is sizing or ducts, new equipment on the same ducts can leave the same complaint behind.
When is AC repair an emergency?
Call for urgent service when there is no cooling in dangerous heat, a burning or electrical smell, a breaker that trips again, water reaching anything electrical, or anyone at home who is especially vulnerable to heat. A comfort complaint can usually be booked. Smoke, fire or another immediate hazard goes to emergency services first; no-cool calls are answered 24/7, nights, weekends and holidays included.
Call now rather than booking online if:
- There is no cooling at all in dangerous heat
- Someone at home is elderly, very young, pregnant or chronically ill
- You smell burning or see smoke or sparking
- The breaker trips again after one reset
- Water is reaching electrical equipment, ceilings or floors
Smoke or fire is a 911 call first. HVAC service follows once the hazard is under control.
(912) 858-3737How do you prevent the next breakdown?
Change or inspect the filter on its own schedule rather than waiting for airflow to fade, keep the outdoor unit clear, pay attention to new noises or cycling, and never ignore recurring water at the air handler. In Pooler, put condensate drainage and humidity performance on the maintenance list alongside the usual coil and electrical checks, and have the system serviced before the summer peak.
Filters on the filter's schedule
The right interval depends on the filter, pets, dust and how hard the system runs. The filter's and the equipment's own instructions come first.
Drains, pans and ducts
The EPA recommends clean drain pans, unobstructed drain lines, and sealed, insulated ducts where they run through unconditioned space such as an attic. All three matter more in a long, humid season.
Judge it by comfort, not just the setpoint
If the house stays clammy, rooms never balance or the system short-cycles, look at airflow, ducts, sizing and moisture removal instead of turning the thermostat down again.
Why Pooler homeowners call Brabham.
Family-owned since 1997, a short drive from Pooler at our shop on Ogeechee Road in Savannah. The diagnostic price before we start, the repair price before any work, 24/7 for no-cool emergencies — and same-day visits when the schedule allows, never promised when it does not.
Diagnostic pricing given up front, before any work starts
24/7 emergency service for no-heat and no-cool calls
Ask about financing on replacements and larger repairs
We meet or beat any verifiable quote on comparable work
If something is not right, we come back and make it right
Trane Authorized Dealer, licensed & insured, background-checked technicians
Pooler AC repair questions.
- Do you provide AC repair in Pooler, GA?
- Yes. Pooler is part of our regular service area, a short drive from our shop on Ogeechee Road in Savannah. Book a visit for a standard repair; for a house with no cooling at all, call (912) 858-3737.
- Can you come to Pooler the same day?
- Often, yes, though it is never promised on a given day. If the house has no cooling at all, call rather than sending a request — emergency service runs 24/7.
- Do you offer emergency AC repair in Pooler?
- Yes, for no-cool calls. Emergency service runs 24/7, including nights, weekends and holidays. Call rather than relying on an online request, and if there is smoke or fire, call 911 first.
- Why is my AC running but not cooling?
- Restricted airflow, a dirty coil, an outdoor-unit or electrical failure, a refrigerant leak or an incorrect charge, or a compressor problem can all do it. The symptom narrows the search but cannot identify the failed part on its own — that takes testing at the system.
- Why is water coming from my AC?
- An air conditioner removes moisture from the air and has to drain it away. A blocked drain line, a dirty or damaged pan, a frozen coil thawing, or a condensate pump problem can all put water where it should not be. The EPA recommends keeping drain pans clean and drain lines flowing freely.
- Why does my Pooler home feel humid even when it is cool?
- Temperature and humidity are different loads. Short runtimes from oversized equipment, airflow problems or other moisture-control issues can leave a house cool but damp. The EPA recommends keeping indoor relative humidity below 60%.
- Can a fairly new AC system still have comfort problems?
- Yes. The equipment can be mechanically healthy while sizing, duct leakage, airflow, refrigerant charge or how it was set up at installation limit comfort. DOE and ENERGY STAR both identify these installation factors, which is why we measure before recommending anything.
- Is my newer AC still under warranty?
- Possibly. Manufacturer warranties usually cover failed parts rather than the labor to replace them, and the length depends on the product and on whether it was registered. Have the model number, serial number and install date ready when you book, and we will check what applies.
- How much does AC repair cost in Pooler?
- The diagnostic is $89, quoted before we start, and the repair is priced and approved before any work. Pooler uses the same Chatham County price list as Savannah: a capacitor replacement is from $179, and a compressor is $1,799–$3,499.
- Should I repair or replace a 10-year-old AC?
- Age alone is not enough. Compare the failure, warranty, condition, refrigerant, comfort history, past repairs and the cost of replacement. ENERGY STAR suggests having equipment over 10 years old evaluated, especially if it is no longer keeping the house comfortable.
- Can an R-22 air conditioner still be repaired?
- Yes. The EPA allows existing R-22 equipment to be serviced. New R-22 has not been produced or imported in the U.S. since 2020, so service relies on reclaimed or previously produced refrigerant, which affects the cost of a large refrigerant repair.
- Can an existing R-410A system still be repaired?
- Yes. The refrigerant transition limits what new equipment is built with; it does not require replacing an existing R-410A system, and those systems can still be repaired and serviced.
- Do you repair heat pumps in Pooler?
- Yes. A heat pump is the air conditioner in summer, so many AC symptoms in Pooler turn out to involve heat-pump equipment. The diagnosis is the same: find the fault, price it, and repair only after you approve.
- Which Pooler neighborhoods do you serve?
- All of Pooler, from the older streets near the center of town to newer communities such as Savannah Quarters, Hamilton Grove, Bridgewater and Harmony. If you are not sure whether an address is covered, call and ask.
Work it out first:Repair or replace?System sizing guideHumidity & comfortSEER2 explained
Sources: Climate: NOAA 1991–2020 Climate Normals, Savannah/Hilton Head International Airport. Population: U.S. Census Bureau, 2020 Census and Vintage 2025 estimates. Sizing, refrigerant charge and duct leakage: U.S. Department of Energy and ENERGY STAR. Indoor humidity and drain pans: U.S. EPA, A Brief Guide to Mold, Moisture and Your Home. R-22: U.S. EPA, homeowner questions on R-22. R-410A: U.S. EPA, Technology Transitions HFC Restrictions by Sector. Replacement guidance: ENERGY STAR. Page updated .
Where to go next.
The rest of what we do here, and the same work in the towns next door.
Need AC repair in Pooler?
Book a visit for a system that is running but not right. For no cooling at all, call — emergency service runs 24/7. The diagnostic price comes first, and nothing is repaired until you approve it.
No heat, or no cooling at all?Call rather than send a request — (912) 858-3737 is answered around the clock.